基于齿面波纹度的齿轮啮合噪声分析理论-学报杂志社

期刊信息

合肥工业大学（自然科学版），2023年12月，第46卷第12期：1635-1641，1658

DOI: 10.3969/j.issn.1003-5060.2023.12.008

作者信息

于振辉 $ ^{1,2} $，夏链 $ ^{1,2,3} $，韩江 $ ^{1,2,3} $，田晓青 $ ^{1,2,3} $

(1. 合肥工业大学机械工程学院，安徽合肥 230009；2. 安徽省智能数控技术及装备工程实验室，安徽合肥 230009；3. 合肥工业大学机械工程国家级实验教学示范中心，安徽合肥 230009)

摘要和关键词

摘要: 文章提出一种基于齿面波纹度的齿轮啮合噪声分析理论,通过对齿轮全齿面的拓扑测量、齿面波纹度分析,对比全齿波纹度图、高阶频谱图的阶次振幅大小与三维形貌图中啮合线、波纹线的接近程度,实现对高速低噪声轮的噪声分析。基于齿面波纹度分析技术,弥补传统齿轮测量在精度一致时无法辨别齿轮啮合噪声的缺点,可在生产周期前期对故障齿轮进行筛选,降低检测成本;基于新能源汽车变速箱,分析输入轴齿轮批次更换时反复出现噪声的原因,对测量的拓扑数据进行波纹度计算。结果显示,齿轮右齿面存在鬼阶和整阶不良,推断在啮合时产生噪声,该分析结果与变速箱台架实验结果一致。

关键词: 新能源汽车；啮合噪声；齿轮测量；齿面波纹度

Authors

YU Zhenhui $ ^{1,2} $, XIA Lian $ ^{1,2,3} $, HAN Jiang $ ^{1,2,3} $, TIAN Xiaoqing $ ^{1,2,3} $

(1. School of Mechanical Engineering, Hefei University of Technology, Hefei 230009, China; 2. Anhui Engineering Laboratory of Intelligent CNC Technology and Equipment, Hefei 230009, China; 3. National Demonstration Center for Experimental Mechanical Engineering Education, Hefei University of Technology, Hefei 230009, China)

Abstract and Keywords

Abstract: In this paper, a gear meshing noise analysis theory based on tooth surface waviness is proposed. Through topological measurement and waviness analysis on full gear tooth surface, the amplitude of ripple above the rotation angle and the high orders of the spectrum are compared. Furthermore, how close the meshing line is to the waviness line in the microtopography is also compared. Then, the noise behavior of high-speed and low-noise gears can be analyzed. The technology of tooth surface waviness analysis can make up for the shortcomings of traditional gear measurement methods that cannot distinguish gear meshing noise under the condition of the same accuracy. Unqualified gears can be removed from the early stage of the production cycle, which reduces a lot of inspection costs. Based on a new energy vehicle gearbox, the reason for repeated noise during the batch replacement of input shaft gears is analyzed. The measured topological data is used for waviness analysis and calculation. The result shows that there is gear order noise and ghost order noise on the right tooth surface of one of the gears. It may cause noise in meshing process. The analysis result is consistent with the experimental result of the gearbox.

Keywords: new energy vehicle; meshing noise; tooth surface detection; tooth surface waviness

基金信息

国家重点研发计划资助项目（2020YFE0201000）；国家自然科学基金资助项目（51875161；52075142）

合肥工业大学学报(自然科学版)

导航菜单

基于齿面波纹度的齿轮啮合噪声分析理论